Picture of Honda CRF 150 RBC/RBD/RBE 12-14 Rear Wheel Bearing Right

Part Description

Honda CRF 150 RBC/RBD/RBE 12-14 Rear Wheel Bearing Right

DID Logo

DID 520 VX X-Ring Chain Gold/Black

DID's VX Chain uses patented X-ring seals. Like O rings, X rings function to seal in lubrication and keep dirt out.

Where the cross section of an O ring is circular, the cross section of an X ring is X, or cross, shaped. This gives the seal additional contact points compared to the O ring, offering superior sealing and protection against dirt and grit getting stuck under the seal.
In addition, when under pressure, an O ring becomes squashed and causes friction. An X ring, when under pressure, diverts this pressure by twisting instead, so an X ring decreases friction between side plates and reduces power loss by 50% of any other type O-ring chain.

DID's X rings have 40% greater wear resistance than an O-ring chain and 36 times that of a DID standard chain; this means more resistance to stretching, bowing and warping, and smoother handling. With proper maintenance, an X-ring chain will last longer than any O-ring or unsealed chain.

Specification
Pin Length Roller Diameter Plate Thickness Weight Tensile Strength Colour
18.70 10.22mm 2.0mm 1.52kg per 100 links 36.5KN Gold and Black

Sealed chains require lubrication every 500km (300 miles) in order to prevent surface rust and ensure performance.

Related Products

Chain Adjusters

Chain Lube

Chain Tools

Delivery and Returns

We want you to be happy with your purchase. If you're not, just return the products to our warehouse. Unless faulty, we'd like this to be within 30 days of purchase. Exceptions apply to certain products.

Read our full returns policies

Wheel Bearing
Sealed Bearing 2RS - DDU

All the wheel bearing we supply are 2RS - DDU.

Double sealed and ready lubricated with premium grease for added protection against dirt and water ingress and are made of high strength AISI 52100 chrome steel components for the rolling elements and the inner and outer rings; to ABEC 1 dimensional tolerances and C3 radial clearance tolerance.

The bearings also undergo electronic noise and vibration testing according to ANSI/AFBMA Standard 13-1987.



Care And Maintenance

Although bearings are subjected to large amounts of stress and are continually being used to fulfil various duties, they are precision made and typically last a long time (bearing failure is often due to improper installation and fitting). However high-mileage bikes and dirt bikes, which are exposed to a lot of mud and water, can become vulnerable and require attention sooner than expected.

... Read more » Wheel Bearing Information

Instructional DVD- A Guide For Replacing Your Headstock Bearings

REPLACE YOUR HEADSTOCK BEARINGS

DONT JUST READ ABOUT HOW TO DO IT,
WATCH IT!!

The complete guide to checking, removing, replacing and upgrading your headstock bearings. Professionally filmed in our studio, Nick Hine shows you exactly how to do each job - with clear, close-up shots, tips, advice and techniques that enable you to do a professional finish - even if you have no experience.

All DVDs start and end with the bike on the ground, They don't miss out any steps and always use standard home garage tools where possible and show you how to make your own special tools where necessary. We explain why you need to do each task and try to give you a good understanding of the principles behind each job.

THIS COMPREHENSIVE 36 MINUTE DVD SHOWS YOU HOW TO
  • Accurately check your headstock bearings for wear and play
  • Safely jack up and support your bike
  • Remove the wheel, fairings, forks and of course headstock
  • Remove the old bearings and races from the bike and the headstock
  • Make your own special tools
  • Fit the new bearings and races
  • Grease, install and adjust the headstock
  • Torque up your bolts in the correct order
  • Rebuild your bike
  • ... Read more » DVD Guide - How To Replace Headrace Bearings

WMD

WORLD'S END MOTORCYCLES DISTRIBUTION

Supplying quality after market motorcycle parts direct to the trade